Fury Road V8 Interceptor

[AL775]

Hi everyone, here is my Fury Road version of the Interceptor. I used the Aoshima Model for this build. Its a work in progress. Hope you like it

WP_20150720_050.jpg (118.09 KiB) Viewed 7921 times

WP_20150720_046.jpg (120.71 KiB) Viewed 7921 times

WP_20150720_040.jpg (99.5 KiB) Viewed 7921 times

WP_20150720_031.jpg (125 KiB) Viewed 7921 times

WP_20150720_037.jpg (117.07 KiB) Viewed 7921 times

[AL775]

Here are some more photos. Apologies for the quality:

WP_20150720_053.jpg (114.36 KiB) Viewed 7919 times

WP_20150720_059.jpg (115.19 KiB) Viewed 7919 times

WP_20150720_052.jpg (110.33 KiB) Viewed 7919 times

[Taipan]

Hey! Welcome to the forum!

Looking good so far, I reckon the rag-tyre is going to be a bit of a challenge. I got you some pics from Top Gear magazine that show some detail of the car, might come in handy:

Interceptor top.jpg (318.13 KiB) Viewed 7914 times

Driver door.jpg (42.03 KiB) Viewed 7914 times

floor.jpg (48.63 KiB) Viewed 7914 times

blown tyre.jpg (56.48 KiB) Viewed 7914 times

interior.jpg (125.93 KiB) Viewed 7914 times

[Wozza]

Great work, glad you fixed that top spoiler too! I always hated that on this kit....

[AL775]

Hey! Welcome to the forum!

Looking good so far, I reckon the rag-tyre is going to be a bit of a challenge. I got you some pics from Top Gear magazine that show some detail of the car, might come in handy:

Thanks for your suggestions Taipan . Yes the Tyre is such a challenge! I am still thinking of ways to try and get it right! I also want to maybe even change the rims to be more accurate to the actual car. Currently the rims are the stock Aoshima Kit. Hopefully someone knows a website/source where I can purchase the correct rims?

Great work, glad you fixed that top spoiler too! I always hated that on this kit....

Thanks for your comcent Wozza! The spoiler required a lot of careful filing to get rid of that extra plastic. I then had to use model filler to fill in that big gap after the filing.

[Hetzer]

That looks great. That roof spoiler sure s a bitch, I wouldn't mind if it be solid but they just had to make it hollow too

[PhilC]

And that is the best way to go about fixing that roof spoiler up i think. Pre fill it with a putty and then cut away the back of it afterwards. I did that with the one i started and it worked out pretty good.

AL you're FR Interceptor is looking great there. Everything from the smashed cover on the front to the collection of stuff in the back looks the part. Nice work!

[rockatansky4073]

This is killer, man!

I'm building Razor cola and the Fury Road BoB, using the Cavalier kit.

The tyres on them are rubber, so it makes the rag tyre thing easier.
I did exactly like the movie and sewed wire through the rubber criss crossing the rags to the tyre.
Very tedious work, but looks great.

Loving that the Fury Road Bob is not getting ignored since Part 2's still gets most the attention.

[Taipan]

BTW, notice the spot where the boot spoiler used to be, nice little detail, made to tie the movie in with the game, at least that was the plan.

[rockatansky4073]

Those boot spoilers are pricks to cut and file off the Cavalier.
Too deep and you'll make it uneven and stuck trying to file the whole area down to match.
Not enough and critics like us fans will spot it